Muutke küpsiste eelistusi

E-raamat: Challenges in Mechanics of Biological Systems and Materials, Thermomechanics and Infrared Imaging, Time Dependent Materials and Residual Stress, Volume 2: Proceedings of the 2023 Annual Conference & Exposition on Experimental and Applied Mechanics 2024 ed. [Taylor & Francis e-raamat]

Edited by , Edited by , Edited by , Edited by , Edited by , Edited by , Edited by , Edited by , Edited by , Edited by
Teised raamatud teemal:
  • Taylor & Francis e-raamat
  • Raamatu hind pole hetkel teada
Challenges in Mechanics of Biological Systems and Materials, Thermomechanics and Infrared Imaging, Time Dependent Materials and Residual Stress, Volume 2: Proceedings of the 2023 Annual Conference & Exposition on Experimental and Applied Mechanics 2024 ed.Suurem pilt
Teised raamatud teemal:
Taylor & Francis e-raamatudRohkem infot Taylor & Francis e-raamatute kohta
Challenges in Mechanics of Biological Systems and Materials, Thermomechanics and Infrared Imaging,  Time Dependent Materials and Residual Stress, Volume 2 of the Proceedings of the 2023 SEM Annual Conference & Exposition on Experimental and Applied Mechanics, the second volume of five from the Conference, brings together contributions to this important area of research and engineering.  The collection presents early findings and case studies on fundamental and applied aspects of Experimental Mechanics, including papers in the following general technical research areas: 





Advanced Thermographic Techniques for SHM





AM Composites and Polymers





Experimental Techniques in Biomechanics and Mechanobiology





Inverse Methodologies and Uncertainties in the Identification of Residual Stresses, Residual Stress IV





Low Cost Thermographic Applications





Multiscale Mechanics of Biological Materials





NDE and Process Monitoring





Residual Stress





Thermomechanics Time Dependence in Porous and Soft Materials
Chapter
1. Development of PEEK matrix polymer composite and additive manufacturing by pellet extrusion method.
Chapter
2. Parkinsonian Hand Tremor Mitigation with Enhanced Wearable Device.
Chapter
3. Quantitative Measurement of Viscoelastic Properties of Soft Membranes Subjected to Finite Deformations based on Optical Coherence Elastography.
Chapter
4. Open Source Contour Method Analysis for Assessing Residual Stress in Weldments.
Chapter
5. Variation of initial bulk residual stresses in aluminum alloy 7050-T7451 and its effect on distortion of thin-walled structural parts.
Chapter
6. On the Use of iDIC (Integrated Digital Image Correlation) for the Slitting Method.
Chapter
7. A rapid procedure to re-construct S/N curve by using harmonic components of thermal signal.
Chapter
8. Rapid Fatigue Characterisation via Infrared Thermography of AM-CM Composites.
Chapter
9. Condition Assessment by Thermal Emission (CATE) for in situ monitoring of fatigue crack growth.
Chapter
10. Effect of geometrical discontinuities on mode shapes stress maps using infrared thermography.
Chapter
11. Induction thermography: influence of testing parameters for different crack geometry.
Chapter
12. Numerical Simulation of the Heat Dissipation During the Fatigue Test.
Chapter
13. A full experimental characterization of aged Nitrile Butadiene Rubbers (NBR).
Chapter
14. Characterization of the Effect of Cold Joints and Functional Grading in Stepwise Constructed Tensile Dog Bones with Embedded Digital Image Correlation.
Christian FranckUniversity of Wisconsin-Madison, WI, USA;Karen KaszaColumbia University, NY, USA;Jon Estrada, University of Michigan, MI, USA;Rosa De FinisUniversity of Salento, Italy;Geir ÓlafssonUniversity of Bristol, UK;Suhasini GururajaAuburn University, AL, USA;Jevan FurmanskiUniversity of Dayton Research Institute, OH, USA;Aaron ForsterNational Institute of Standards and Technology, MD, USA;Pavan KolluruTexas A&M University, TX, USA;Mike PrimeLos Alamos National Laboratory, NM, USA;Tom BerfieldUniversity of Louisville, KY, USA;Cahit AydinerBogazici Universitesi, Turkey.
Püsilink: https://www.kriso.ee/db/9788743804185_pe.html