Muutke küpsiste eelistusi

E-raamat: Computational Methods and Experimental Measurements XIII

Edited by , Edited by (Wessex Institut of Technology)
  • Formaat - PDF+DRM
  • Hind: 635,15 €*
  • * hind on lõplik, st. muud allahindlused enam ei rakendu
  • Lisa ostukorvi
  • Lisa soovinimekirja
  • See e-raamat on mõeldud ainult isiklikuks kasutamiseks. E-raamatuid ei saa tagastada.

DRM piirangud

  • Kopeerimine (copy/paste):

    ei ole lubatud

  • Printimine:

    ei ole lubatud

  • Kasutamine:

    Digitaalõiguste kaitse (DRM)
    Kirjastus on väljastanud selle e-raamatu krüpteeritud kujul, mis tähendab, et selle lugemiseks peate installeerima spetsiaalse tarkvara. Samuti peate looma endale  Adobe ID Rohkem infot siin. E-raamatut saab lugeda 1 kasutaja ning alla laadida kuni 6'de seadmesse (kõik autoriseeritud sama Adobe ID-ga).

    Vajalik tarkvara
    Mobiilsetes seadmetes (telefon või tahvelarvuti) lugemiseks peate installeerima selle tasuta rakenduse: PocketBook Reader (iOS / Android)

    PC või Mac seadmes lugemiseks peate installima Adobe Digital Editionsi (Seeon tasuta rakendus spetsiaalselt e-raamatute lugemiseks. Seda ei tohi segamini ajada Adober Reader'iga, mis tõenäoliselt on juba teie arvutisse installeeritud )

    Seda e-raamatut ei saa lugeda Amazon Kindle's. 

Recent advances in the speed and efficiency of computers, and in computational techniques, have been major factors in the growth of numerical methods that now affect not only engineering, but our everyday lives. However, even if computational codes have been increasingly successful in simulating engineering problems, there still exists a wide range of them that need a comprehensive validation that can be accomplished only by means of experimental analysis. In the meantime, experimental measurements have become so sophisticated that experiments must very often be carried out with the help of computers and the data obtained have to be processed by means of numerical methods.This book contains most of the papers presented at the 13th International Conference on Computational Methods and Experimental Measurements (CMEM/07) held in Prague in 2007.The primary aim of the meeting was to offer to the International Scientific Community an arena for the presentation and exchange of advanced approaches and applications in the fields of numerical methods and experimental determinations, with the principal attention and emphasis being devoted to their beneficial interaction and mutual influence.
Section 1: Computational and experimental methods
Direct simulations of fluid dynamic sounds by the finite difference lattice Boltzmann method
3(10)
M. Tsutahara
A. Tamura
S. Tajiri
W. Long
Spectral analysis of a transitional separated-reattached flow using Fourier and wavelet transforms
13(12)
I. E. Abdalla
M. J. Cook
Observation of solid fuel in a supersonic flowfield
25(10)
J. M. Char
U. K. Hsu
Temperature field at the twin-roll casting of aluminium alloys: computational model and measurements
35(10)
H. Gjerkes
S. Hartman
R. Vertnik
B. Sarler
A newly developed test rig for the study of thermal fatigue
45(10)
M. Fazarinc
R. Turk
G. Kugler
M. Tercelj
Numerical simulation with flow feature extraction of a propeller turbine unsteady rotor-stator interaction
55(10)
J.-M. Gagnon
C. Deschenes
Computer and experimental study of the gate dielectric in a memory transistor
65(10)
R. Avichail-Bibi
D. Fuks
A. Kiv
Ya. Roizin
Electron band structure and properties of disordered semiconductor compound alloys
75(10)
D. Alexandrov
K. S. A. Butcher
T. L. Tansley
Fast calculation of the dimensioning factors of the railway power supply system
85(12)
L. Abrahamsson
L. Soder
A formulation of a multi-wave elastodynamic infinite element
97(12)
K. Kazakov
Section 2: Experimental and computational analysis
Influence of the collision speed and angle of a bullet: experimental reconstruction of bullet configuration and FE-analysis
109(8)
H. Sakamoto
T. Hiwatashi
T. Yamaguchi
M. Yamamoto
Influence of the cross-section shape on the lateral torsional buckling capacity
117(10)
D. Djuric-Mijovic
M. Trajkovic
Computational fluid dynamic modelling and simulation evaluation of the plume evacuation device efficiencies
127(10)
F. Farshad
H. Rieke
L. C. LaHaye
S. C. Nulu
Flow estimations through spillways under submerged tidal conditions
137(10)
P. D. Scarlatos
M. Ansar
Z. Chen
Analysis of the wave-flow interaction with submerged breakwaters
147(8)
A. C. Neves
F. Veloso Gomes
F. Taveira Pinto
An application of an edge effect based vacuum blower to a lyophilizer
155(10)
M. Kitamura
M. Tsutahara
H. Sasaki
The wavelength reconstruction from toroidal spectrometer image data
165(6)
J. Blazej
M. Tamas
L. Pina
A. Jancarek
S. Palinek
P. Vrba
M. Vrbova
Numerical noise in satellite laser ranging data processing
171(6)
J. Blazej
I. Prochazka
Expanding the definition of multivariate correlation
177(8)
W. Conley
3D analysis of solid reinforced concrete beams subjected to combined load of bending, torsion and shear
185(10)
A. S. Alnuaimi
Use of correlation of iron loss and copper loss for improving the efficiency of three phase squirrel cage induction motors
195(10)
B. B. Saanane
A. H. Nzali
D. J. Chambega
Effect of Zr addition on the fatigue strength of Cu-6Ni-2Mn-2Sn-2Al alloy
205(10)
M. Goto
S.-Z. Han
C.-J. Kim
N. Kawagoishi
An analysis of superplastic free forming at constant pressure
215(10)
G. Giuliano
S. Franchitti
A mathematical model approach to a glycerolysis reaction for monoacylglycerol production
225(8)
B. Cheirsilp
A. H-Kittikul
Evaluation of experimental procedures for confined concrete columns using 3D finite element analyses
233(10)
H. O. Kolcsal
C. Karakoc
Z. Polat
T. Turgay
S. Akgun
Geometrically nonlinear static analysis of 3D trusses using the arc-length method
243(12)
G. A. Hrinda
Section 3: Fluid flow
On the accuracy of integral representation of differential operators in Lagrangian blob mesh-less methods
255(12)
C. Golia
B. Buonomo
Construction of a non-Newtonian fluid model based on the finite difference lattice Boltzmann method
267(10)
S. Tajiri
M. Tsutahara
Experimental measurements for the control of a vortex shaft theoretical model
277(10)
G. Ciaravino
L. Ciaravino
G. Pulci Doria
Stability of stratified spin-up flows
287(10)
S. A. Smirnov
On the relation between geometric and flow properties of a miniaturized fluid oscillator
297(10)
J. O. Sotero-Esteva
R. Furlan
J. J. Santiago-Aviles
On-stream floodplain storage: experimental research
307(12)
G. De Martino
F. De Paola
G. Marini
A. Ranucci
Analytical and hydraulic model study of highway culvert sand-blockages
319(10)
M. Kamaka
E. Cheng
M. Teng
C. Matsuda
Incorporating computational fluid dynamics in the design/build of a single family residence
329(10)
J. Chang
N. Rosemann
Section 4: Salts in porous materials (Special session organised by Professor R. Cerny)
Mathematical modeling of water and salt transport in porous materials
339(10)
R. Cerny
Determination of water and salt transport parameters of porous materials using methods of inverse modelling
349(8)
L. Fiala
Z. Pavlik
M. Pavlikova
R. Cerny
Effect of metakaolin on chloride binding in lime-based composites
357(10)
R. Pernicova
M. Pavlikova
R. Cerny
Computational simulation of the effect of crystallization inhibitors on salt transport and crystallization in porous materials
367(10)
J. Kelnar
J. Madera
R. Cerny
Desalination of historical masonry using hydrophilic mineral wool boards
377(12)
P. Michalek
V. Tydlitat
M. Jerman
R. Cerny
Section 5: Heat transfer
Numerical investigation on natural convection in asymmetric channel-chimney systems
389(10)
A. Andreozzi
B. Buonomo
O. Manca
Plate distance effect on mixed convection in horizontal channels heated from below
399(12)
G. Foglia
O. Manca
S. Nardini
Numerical analysis of mixed convection in air in an inclined channel with a moving plate
411(14)
A. Andreozzi
N. Bianco
G. Lacasa
V. Naso
A numerical method for studying impulsively generated convection from heated tubes
425(12)
S. J. D. D'Alessio
Heat transfer in a ribbed square duct by Large-Eddy-Simulation
437(10)
O. Labbe
Effect of thermal boundary conditions on conjugate natural convection flow in vertical eccentric annuli
447(10)
A. Jamal
M. A. I. El-Shaarawi
E. M. A. Mokheimer
Foam flow turn influence on the in-line tube bundle heat transfer intensity
457(8)
J. Gylys
S. Sinkunas
T. Zdankus
V. Giedraitis
A. Balcius
Importance of experimental measurements and simulations for ``sludge-to-energy'' systems
465(10)
L. Houdkova
J. Boran
T. Elsaßer
P. Stehlik
Simulation of thermal barrier coating behaviour during dynamic thermal loading by the Exodus method
475(10)
J. Sroub
M. Honner
Z. Vesely
Forced convection in a variable section axisymmetric channel with different porous layers and heat generation
485(10)
E. Pilevne
A. Misirlioglu
Comparison of h-, p- and hp-adaptation for convective heat transfer
495(10)
D. W. Pepper
X. Wang
Modified spherical harmonics method for one-speed transport equation with anisotropic scattering
505(12)
M. S. Li
B. Yang
Section 6: Structural and stress analysis
Inverse variational principle based coupled modeling of underground structures
517(10)
P. Prochazka
Elastic-plastic simulation of plate with a blunt slit subjected to uni-axial tension
527(10)
S. Ohtaki
S. Kobayashi
T. Yamamoto
A simplified shear strength evaluation model for reinforced concrete corbels
537(10)
J. K. Lu
S. Y. Kuo
J. Y. Lin
S. H. Hsu
Post-buckling behaviour of a slender beam in a circular tube, under axial load
547(10)
M. Gh. Munteanu
A. Barraco
Structural properties of a new material made of waste paper
557(12)
J. Santamaria
B. Fuller
A. Fafitis
Non-Hertzian rolling contact stress analysis
569(10)
C. H. Liu
W.-E. Hsu
The areolar strain concept applied to elasticity
579(10)
I. D. Kotchergenko
Methodology for the manufacture of smart composites with thermoplastic matrix
589(12)
L. Elsoufi
K. Khalil
R. Lachat
W. Charon
M. Zoaeter
Experimental investigation on the folding of axially crushed hexagonal tubes
601(10)
M. R. Said
A. A. Mokhtar
A. Alias
A. Ibrahim
Application of the shakedown analysis in the elastic: plastic assessment of cracked plates
611(12)
M. A. Belouchrani
Section 7: Experiments and analysis of reinforced concrete members (Special session organised by Professor C. G. Karayannis)
Cyclic testing of reinforced concrete beam-column joints with crossed inclined bars
623(10)
C. E. Chalioris
C. G. Karayannis
M. I. Favvata
Tests and analysis of reinforced concrete beams under torsion retrofitted with FRP strips
633(10)
C. E. Chalioris
Influence of masonry strength and rectangular spiral shear reinforcement on infilled RC frames under cyclic loading
643(12)
D. J. Kakaletsis
Application of the Cement Hydration Equation in self-compacting concrete's compressive strength
655(16)
N. Anagnostopoulos
A. Gergiadis
K. K. Sideris
Section 8: Structural dynamics
Response of a double system beam and string with an elastic layer to the dynamic excitations
671(10)
L. Fryba
C. Fischer
Sh. Urushadze
Excessive accelerations in bridges for Korea high-speed railway
681(10)
J. W. Kwark
J. R. Cho
W. J. Chin
B. S. Kim
E. K. Cho
Parameter identification for multiple modes of cable-stayed bridge cables using ambient vibration measurements from a single station
691(10)
W.-H. Wu
C.-A. Liao
C.-C. Chen
Experimental evaluation of dynamic properties of an incrementally prestressed concrete girder railway bridge
701(10)
S. I. Kim
I. H. Yeo
N. S. Kim
J. W. Kwark
J. S. Lee
Section 9: Dynamics and vibrations
A model of spur gears supported by ball bearings
711(12)
F. Viadero
A. Fernandez del Rincon
R. Sancibrian
P. Garcia Fernandez
A. de Juan
On a numerical model of a complete washing machine
723(14)
T. Argentini
M. Belloli
N. Gaudiano
G. Fraternale
F. Panetta
D. Sabato
M. Vanali
Section 10: Detection and signal processing (Special session organised by Professor Z. Bielecki)
EUV detection system with calibrated responsivity
737(10)
J. Mikolajczyk
Z. Bielecki
Analysis of radiating structures placed on multilayer dielectric
747(10)
M. Wnuk
M. Bugaj
Method of signal processing in passive infrared detectors for security systems
757(12)
H. Madura
Influence of the displacement effect on compressed LFM signal parameters
769(10)
A. Kawalec
Cz. Lesnik
W. Komorniczak
W. Czarnecki
J. Pietrasinski
A comparison of estimation accuracy by the use of KF, EKF & UKF filters
779(12)
S. Konatowski
A. T. Pieniezny
Novel method for watermarking system operating on the HF and VHF radio links
791(10)
Z. Piotrowski
P. Gajewski
Optoelectronic system for phase array antenna beam steering
801(8)
E. Sedek
Z. Bielecki
M. Muszkowski
W. Kolosowski
G. Rozanski
M. Wnuk
Nitrogen dioxide detection using an optoelectronic sensor
809(10)
Z. Bielecki
W. Kolosowski
G. Rozanski
E. Sedek
J. Wojtas
Automatic processing analysis of infrared images for monitoring pantograph catenary interactions
819(10)
A. Balestrino
O. Bruno
A. Landi
L. Sani
Architectural hot-swap in NURBS surfaces: versioning of case studies, work in progress
829(12)
A. Prichard-Schmitzberger
Section 11: Advances in measurements and experiments
Development of advanced instrumentation for operational oceanography
841(10)
G. Zappala
In-situ measurement of formwork pressures generated by Self-Compacting Concrete
851(10)
M. M. Giammatteo
A. Gregori
G. Totani
Evaluation of phenolic resins from one-pot microwave synthesis
861(10)
A. Britten
M. M. MacIntyre
A. Miadonye
Modern techniques of measure and control of deformations -- an experimental test: Senerchia landslide
871(12)
M. Caprioli
G. Strisciuglio
Section 12: Industrial applications
Calculating the dilution between successive trainloads of iron ore during processing
883(10)
J. E. Everett
Rock bumps due to the creation of a dislocation during deep mining
893(10)
V. Dolezel
P. Prochazka
Author Index 903